
Ring Doorbell is the best smart doorbell to monitor your front door and keep it secure. This device is equipped with a number of light patterns and light indicators to aware of its status, connection, and different functional activities on the doorbell. One such indicator is the Blue flashing light.
Ring doorbell has a LED light on its peephole cam. If you’ve just installed a new Ring Doorbell, this blue flashing LED light indicates that the doorbell is in charging status.
Why Ring Doorbell Flashing Blue Light
LED around the button spins Blue:
The blue light spins around the button when you simply press the Ring doorbell.
Blue light moving upwards:
When you see a Blue light simply going up and ending at the upper end of your Ring doorbell LED position, it indicates that Doorbell is connecting with your network connection. It usually happens when you set up your Ring doorbell.
Blue light is flashing on and off for a second:
When you see your Ring Doorbell’s LED light flash on and after a second, it turns off, it indicates that the Ring doorbell is going to reboot. The camera is going to operate and record its front view.
Solid Blue Light:
When you see simple solid Blue light on your Ring doorbell, it means that the speaker of the doorbell has been enabled which is used for a conversation and you can use it from your home to listen to outsiders.

Four LEDS flash four times:
It basically indicates your Ring doorbell setup completion when you first install your doorbell which may take an hour to complete the installation and enable the doorbell ready to use.
Flashing burst of Blue light:
When you find any setup error or any issues with your Ring doorbell, you restore your settings to a factory which shows you a rapid burst of flashing blue light after which you see a spinning white light.
How To Fix Ring Doorbell Flashing Blue
If you are unable to find specific reasons for the Blue light on your Ring Doorbell from the above, you can expect and explore the following issues related to your Ring doorbell Blue light.
Wi-Fi Issues:
Blue light flashes when your doorbell tries to connect with your Wi-Fi network and it is not able to connect with your network. So, the Blue light seems going upward in the ring.
Usually, it may be stuck in the middle due to low network speed which causes the Blue light on the Ring doorbell to flash. When the setup is completed, you will see four LEDs flash four times.
A. Check Wi-Fi Signal on Your Ring Doorbell
B. Fix Internet issues on a Ring Doorbell:
Outdated Software
You may get performance issues and compatibility errors due to outdated software. This might be possible that the Blue light on your doorbell is due to this outdated software.
To ensure your Ring device is up to date, you can check for and install any available software updates through the Ring app. Here’s how:
Did you know💡
The LED light on a Ring doorbell can be customized in terms of brightness and color to fit the style and needs of your home. This allows you to personalize the device to your liking and create a unique look for your front porch.
Another interesting feature of the LED light on Ring doorbells is its ability to act as a deterrent for potential intruders. When the doorbell is triggered, the LED light illuminates and alerts anyone nearby that their activity is being monitored. This can provide added peace of mind and help keep your home safe.
Power Issue
You can check the required power for your Ring doorbell in “Device Health” from your app where you can also check any system update.
Identify improper Power causing Blue light:
Fix Power Issues to Resolve Flashing Blue Light
- Check the battery level: Make sure that the battery has enough charge to power the doorbell. You can check the Battery level in the Ring app under Devices.
Related:
- Check the wiring: If the doorbell is hardwired, check the wiring connections to ensure they are tight and secure.
- Try a different power source: If you have a spare battery, try using it to see if it resolves the issue. If you have another power source available, try using it to see if it resolves the issue.
Try Triggering Alarm
You can trigger an alert using either the doorbell or your mobile phone app. So, you must confirm whether there is a bug in Ring software. If you don’t get a positive response, you must reset your Ring doorbell.
Related:
Ring Doorbell Blue light while charging
First and second generations Ring doorbells are charged by connecting their back port with a power adapter.
When the battery is in charging mode, it will be blinking Blue while charging and it will turn solid blue light when the charging has been completed.
Ring newer generations have batteries that can be plugged out and charged externally. Ring doorbell blinks blue and the light goes on and off when the battery is not inside.
But, when you insert the battery again, it takes time to set up. The doorbell’s four LEDs flash again four times upon the completion of the setup. But, it may take a little longer to set up when you first install your Ring doorbell.
Ring Chime Flashing Blue Light
Enjoy Reading Too:
Meaning of Blinking Blue Light
Fix Ring Doorbell with Continuous Blue Flashing Light
Hard Reset is a beneficial method in the case of a Continuous Blue flashing light. To perform a hard reset on your Ring doorbell, follow these steps:
- Disconnect the doorbell from power: Remove the doorbell from its power source by disconnecting it from the wiring or unplugging it from the outlet.
- Press and hold the button: Locate the reset button on the back of the Ring doorbell. Press and hold the button for 15 seconds.
- Reconnect the power: After holding the reset button for 15 seconds, reconnect the doorbell to its power source.
- Wait for the light pattern: Wait for the light pattern on the doorbell to change from a solid white light to a flashing blue light. This indicates that the doorbell has reset and is ready to be set up again.
Note: The reset process may erase all of your doorbell settings, including Wi-Fi connection information. Make sure to have your Wi-Fi network information handy when setting up the doorbell again.
Recommendation:
Contact Ring Support
If none of the above solutions have worked for you, don’t worry because this is not your fault. This issue is in your Ring doorbell device. You can contact your Ring support.
You can also explain about your warranty. If your Doorbell is in the warranty period, you can get a replacement.
Conclusion
The blue flashing light on a Ring doorbell typically indicates that the device is in setup mode and is ready to be connected to your home’s Wi-Fi network. If the light continues to flash blue after setup is complete, it could indicate that the doorbell is experiencing a connectivity issue and may need to be reset or have its firmware updated.
Frequently Asked Questions
Do I have to charge my Ring Doorbell if it is hardwired?
Yes! Your Ring doorbell gets charged through its wire and the power in the doorbell is used to give power to different operational activities in Ring doorbell.
Can a Ring Doorbell continue to operate while it is charging?
No, the Ring Doorbell will not operate while it is charging. It will only work when it has a sufficient charge or is connected to a hardwired power source.
Is it normal for a Ring Doorbell to flash blue while it is charging?
No, a Ring Doorbell should have a solid blue light while it is charging and it should turn off when the battery is fully charged. A flashing blue light indicates a problem.
About Author

Mahnoor has graduated from AI Security Specific Program at PIASS. She has a special interest in technology especially Automated gadgets and Automated Robots. She has also studied programming and Windows security.
She is now serving as Professor at PIASS teaching a major in AI. She has got herself into content gathering and now at smarthomehut, she often writes about Alexa programming skills and how different automated related devices and how tackle their various issues.
You can find her @
More Info About Smarthomehut